• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

2024-05-27 Adjustable Gear Stick Ball Joint

Been noticing the gear stick tends to shake a lot whilst in 5th gear cos the ball joint was worn & too loose

IMG_20240527_111151.jpg


IMG_20240527_111206.jpg


IMG_20240527_111259.jpg


I tried to print a tighter fitting insert but getting the tolerances right was a PITA and doesn't compensate for wear

IMG_20240527_143321.jpg


So I redesigned a whole new 2-piece mount that can adjust how tight it fits around the ball joint

Ball Joint 2.jpg


Printed & installed new mount

IMG_20240527_205427.jpg


IMG_20240527_205713.jpg


added rivnuts so the mount can be screwed on from the top rather than originally getting underneath

IMG_20240527_191635.jpg


fitment is soo much better, precise & zero play.
gear shift is slightly more precise and doesn't shake around anymore :cool:

IMG_20240527_210605.jpg


IMG_20240527_212005.jpg
 
passenger door is still rattling near the front @ 3k rpm 😤

I tried covering the back of the door card with soft felt

IMG_20240528_153223.jpg


IMG_20240528_154537.jpg


IMG_20240528_161749.jpg


but still buzzes. kinda stops if i push the handle, yet still buzz if I remove that handle?
it's like the inner door frame is resonating louder than any other door.

IMG_20240528_163248.jpg


the only time it's quiet was with everything stripped off the door, soo frustrating
 
passenger door is still rattling near the front @ 3k rpm 😤

I tried covering the back of the door card with soft felt

View attachment 88334

View attachment 88335

View attachment 88336

but still buzzes. kinda stops if i push the handle, yet still buzz if I remove that handle?
it's like the inner door frame is resonating louder than any other door.

View attachment 88337

the only time it's quiet was with everything stripped off the door, soo frustrating


I took the view that my old clunkers were supposed to shake, rattle & roll & that was part of the charm of banger driving?

Perhaps it is easier to try ear plugs or muffs & more fun then it is to chase down every little noise in an old banger? :cool:

bilsom ear muffs at DuckDuckGo
 
I took the view that my old clunkers were supposed to shake, rattle & roll & that was part of the charm of banger driving?

Perhaps it is easier to try ear plugs or muffs & more fun then it is to chase down every little noise in an old banger? :cool:

bilsom ear muffs at DuckDuckGo
I do wear noise cancelling ear buds to help on long journeys but this buzzing door noise is more intrusively annoying. the stiff nismo engine mounts certainly doesn't help with shaking everything to bits lol.

but later on the next post I finally discovered the cause 😁
 
2024-05-29 Weld Rigid Passenger Seat Support

The passenger seat back rest shakes bit more than the drivers seat cos the upper bracket ain't joined directly to the subframe like the drivers side.
So tday I removed the seat

IMG_20240529_134741.jpg


IMG_20240529_134757.jpg


& added the extra bracket to join the two support brackets, making the seat more rigid

IMG_20240529_144113.jpg


IMG_20240529_145701.jpg


IMG_20240529_150245.jpg


IMG_20240529_150853.jpg


sitting in it feels more secure now

IMG_20240529_151602.jpg


ordered a new 2.25" universal 400cell sports cat for the new exhaust manifold layout I'm designing

IMG_20240529_152424.jpg


It's the same 4" diameter as the secondary cat that's under the car

IMG_20240529_153213.jpg


The 400 cell honeycomb density looks exactly the same as the secondary cat, except this honeycomb core is 95mm long

IMG_20240529_152615.jpg


Whereas the secondary cat has a shorter 75mm long core.
The Micra primary cat has a 80mm long core.

IMG_20240529_153130.jpg


So hopefully this thicker universal sports cat will help with emissions
 
Last edited:
2024-05-29 Fixed Door Rattle pt3

Had a nice weekly car meet.
The passenger door was still buzzing annoyingly whilst driving over

IMG_20240529_191542.jpg


I even asked a friend to drive the car at 3k rpm whilst I try to locate the hidden buzzing but no luck

IMG_20240529_204306.jpg


But when looking further, I soon noticed the passenger door stopper had bit more loose play to it compared to the tighter drivers side?
I removed the door stoppers and behold! it finally stopped buzzing and was a quiet drive home 🥳👏

IMG_20240529_221810.jpg


I believe the loose cap on the ends of both door stoppers are the culprit. tack welded them into place

IMG_20240530_150846.jpg


reinstalled & that has FINALLY stopped the buzzing rattles :)
nice n quiet smooth :cool:
 
Last edited:
2024-05-27 Adjustable Gear Stick Ball Joint

Been noticing the gear stick tends to shake a lot whilst in 5th gear cos the ball joint was worn & too loose

View attachment 88323

View attachment 88324

View attachment 88325

I tried to print a tighter fitting insert but getting the tolerances right was a PITA and doesn't compensate for wear

View attachment 88326

So I redesigned a whole new 2-piece mount that can adjust how tight it fits around the ball joint

View attachment 88322

Printed & installed new mount

View attachment 88328

View attachment 88329

added rivnuts so the mount can be screwed on from the top rather than originally getting underneath

View attachment 88327

fitment is soo much better, precise & zero play.
gear shift is slightly more precise and doesn't shake around anymore :cool:

View attachment 88330

View attachment 88331
that's impressive
 
2024-05-31 Electric Window Motor Support Bracket

The heavy electric motor hanging outside the window mechanism can be seen shaking around, which could've contributed to the annoying vibrations

IMG_20240530_155212.jpg


I designed a support brace to anchor the end of the motor onto the door frame

motor support 5.jpg


Printed

IMG_20240531_012313.jpg


IMG_20240531_013431.jpg


Installed and now the motor sits rigid and doesn't shake/vibrate at all now :cool:

IMG_20240531_014030.jpg


IMG_20240531_014210.jpg
 
added some draft excluder tape under the instrument cowl to reduce vibration

IMG_20240601_105730.jpg


brought another cordless grinder which was on sale

IMG_20240601_120014.jpg


visiting Jack for a catch up

IMG_20240601_144014.jpg


replaced the old gear stick cover which had a broken clip

IMG_20240601_143637_1.jpg


IMG_20240601_191923.jpg


old socket tool holder was broke so I designed a better one

Socket Holder 5.jpg


IMG_20240601_221103.jpg


IMG_20240601_221342.jpg
 
swapped from a high mounted alternator to a regular low mounted alternator setup.
wirebrushed all the rust off

IMG_20240613_162457.jpg


painted & fitted

IMG_20240613_183106.jpg


IMG_20240614_124727.jpg


the old belt tensioner with extended adjuster had cracked, making extra rattles but easy enough to reattach

IMG_20240612_144022.jpg


IMG_20240612_155449.jpg


Yorkshire modified show coming up so I polished the wheels

IMG_20240615_113525.jpg


ready for the wet show tomorrow 🙈

IMG_20240615_151738.jpg
 
2024-06-15 Compact Alternator Mounting Bracket

I've been redesigning the turbo layout for the past few years and the standard alternator locations are causing some issues.

The current layout from my previous turbo setup is a high mounted alternator using the air-con mounting brackets

IMG_20240613_182634.jpg


But this fouls the turbo inlet on the new design

high mount.jpg


The original low mounted alternator on the other hand pokes out too far

IMG_20240612_231925.jpg


& can foul the boost pipe going into the intercooler

low mount.jpg


I needed to reposition the alternator low down & very close to the block to give enough room for all the plumbing and avoid touching the electrical terminals too

close mounted.jpg


Lined up the alternator & brackets to the crank pulley

IMG_20240611_230250.jpg


Main bracket tacked up

IMG_20240611_230442.jpg


Welded up

IMG_20240612_135417.jpg


Alternator now rests against the block

IMG_20240612_140637.jpg


To tension the belt, I first tried using the high mounted tensioner

IMG_20240612_221929.jpg


But that was at the wrong angle & couldn't apply any tension

IMG_20240612_221606.jpg


So I redesigned a vertical tensioner bracket integrated into the new mount

IMG_20240615_111911.jpg


Tacked the new piece on. It's a tight fit cos it has to clear the engine mount next to it.

IMG_20240615_134054.jpg


New alternator mount & tensioner completed.
The adjustment screw can be accessed easily from both ends.

IMG_20240615_170234.jpg


IMG_20240615_170005.jpg


Installed the new bracket & now the belt can be tensioned with the alternator sat closer in

IMG_20240615_143700.jpg


IMG_20240615_143705.jpg


IMG_20240615_143655.jpg
 
2024-06-16 Yorkshire Modified Show

Left house from 6am

IMG_20240616_053705.jpg


We gathered near Thirsk for 6:30
as I reverse parked, nathan following behind almost went into me 😬

IMG_20240616_063401.jpg


It was a relatively quiet drive to the venue till we queued at the entrance

IMG_20240616_074310.jpg


it's been a wet few days so the grass entrance was ridiculously muddy 😒

IMG_20240616_075751.jpg


IMG_20240616_080019.jpg


parked up & cleaned off the muck

IMG_20240616_085413.jpg


IMG_20240616_090054.jpg


IMG_20240616_090107.jpg


We were dreading the incoming forcasted downpour but fortunately for most of the morning it's been really sunny & warm for everyone to enjoy the show 😎

IMG_20240616_090838.jpg


IMG_20240616_100502.jpg


During the show I quickly swapped over to the new alternator mount

IMG_20240616_092202.jpg


it clears the engine mount fine and run ok with no noise 😎👍

IMG_20240616_093339.jpg


After lunchtime the forcasted rain comes over and briefly soaks everything 😅⛈️

IMG_20240616_114449.jpg


It soon passed and later we all took a group photo by the pond 🙌

448260849_10233936610259562_422904131611597934_n.jpg


448375510_10233936611139584_3858504733424277339_n.jpg


IMG_20240616_140643.jpg


IMG_20240616_141306.jpg


IMG_20240616_141337.jpg


IMG_20240616_151137.jpg


IMG_20240616_151426.jpg


It was a lovely group drive home in the sun.
Rinsed the mud off before parking it home

IMG_20240616_173048.jpg


IMG_20240616_174226.jpg
 
2024-06-20 Machining Gripper LSD Cover Plate

With the old LSD modelled & machining process planned, it's time to go ahead and make the new cover

cover plate.jpg


The little mini lathe can only make 0.1mm cuts at a time (or else it'll keep chattering)
so it took a looong time and lots of swarf to machine away 19mm x 85mm of steel 😴

IMG_20240620_195109.jpg


drilled & bored the center hole

IMG_20240620_211754.jpg


the next task is to flip it over and machine the other side before I drill the screw holes last
 
flipped the piece over & carefully machined the opposite face as precise as possible

IMG_20240621_165434.jpg


IMG_20240621_185559.jpg


to accurately drill the screw holes, I'll use the old cover plate as a template.
position it concentric against the machined piece using dial gauge to center it

IMG_20240621_190330.jpg


tack weld into place to secure it

IMG_20240621_201252.jpg


using my power drill adapter to make each hole and locking the lathe chuck into each angle using this square wedge tool I made underneath

IMG_20240621_202719.jpg


IMG_20240621_204251.jpg
 
finished drilling all 12 holes

IMG_20240622_122036.jpg


removed the old cover, drilled the flat countersunk holes for the screw heads using my modified step drill

IMG_20240622_125024.jpg


after days of machining I finally have a new & stronger cover plate for my diff

IMG_20240622_130714.jpg


IMG_20240622_130737.jpg


proud of how good it turned out and how precise it fits :love::cool:

IMG_20240622_131055.jpg


I can't wait to reinstall it soon while also fixing the rattling new clutch disc
 
replaced the auxilary belt which was very worn

IMG_20240626_134123.jpg


the new alternator mounting also required a shorter belt within the min/max range of 6pk660-6pk715
so I ordered a 6pk673 belt

IMG_20240627_123740.jpg


and now both belts are fresh & quiet

IMG_20240627_124037.jpg
 
2024-06-27 LED Light Wand for Night Painting

I was inspired one day to make this long LED light wand powered by a 12v battery so that when I do light painting around the car I get more light coverage

IMG_20240626_234939.jpg


it was midnight, dark & quiet which was great time to wonder out to a dark spot to play around with the lighting and the results are awesome :cool:

IMG_20240627_003449.jpg


IMG_20240627_003041.jpg


IMG_20240627_003759.jpg


IMG_20240627_003905.jpg


IMG_20240627_004009.jpg


the next version would be to make an RGB light wand 🥳
 
2024-06-27 LSD Bearing Separater

To remove the old bearing off the LSD I needed a bearing separater.
Most of them cost over £30-100 but I managed to find a local screwfix that sells it for just £19 👍

IMG_20240627_134430.jpg


the tool wasnt big enough to reach around the back side of the bearing so I carefully cut the bearing cage off to expose the inner race

IMG_20240627_135704.jpg


IMG_20240627_135832.jpg


the 1st attempt was layout like this but the clamping & pulling forces was simply bending & buckling the clamshell upwards

IMG_20240627_140216.jpg


then I tried inverting the tool so the clamping force counteracts the pulling force and that worked

IMG_20240627_140722.jpg


inner race removed

IMG_20240627_163152.jpg


the bearings were fitted by some dodgy gearbox shop back in 2011 and there are marks on the spindle indicating the old bearing may have initially been pressed in wonky.
looking at the speedo gear retainer plate, notice the 2 locating tabs that slot loosely onto the two locating notches on the LSD body where it looks like it wasn't kept in place and was squashed by the bearing during install.

the ham fisted person who badly fitted my bearings must've yanked the hydraulic press soo hard to deform those two retaining tabs, I suspect this neglect might have started a tiny crack on the cover plate (around those 2 weak drilled holes near the spindle) and the crack grew through the 8yrs of daily/track use until it fell apart in 2019 🙄

IMG_20240627_163201.jpg


IMG_20240627_164018.jpg


this is the speedo ring gear

IMG_20240627_163309.jpg


IMG_20240627_163319.jpg
 
2024-06-28 DIY Hydraulic Press

Rather than spend another fortune buying a big expensive press to install the new bearings, I designed my own hydraulic press utilizing a small spare 2ton bottle jack I had in storage and a thick steel tubing I got from Jack sheen

hydraulic press 1.jpg


I'd install the bearings with the LSD split apart so I don't risk cracking the cover plate again.
the bearing would be fitted like this

hydraulic press 1 - diff casing.jpg


for the shorter/smaller cover plate, the tip of the bottle jack shaft can be fully extended allowing the press to reach down

hydraulic press 1 - cover plate.jpg


I cut the 40x40mm tubes into lengths

IMG_20240628_164303.jpg


welded up the frame, ensuring it's square & straight

IMG_20240628_173925.jpg


IMG_20240628_182146.jpg


welded the sliding base into position

IMG_20240628_201334.jpg


machining this little locating recess which keeps the screw tip of the bottle jack steady on the frame while allowing it to be adjusted

IMG_20240628_204548.jpg


completed the new press

IMG_20240628_210735.jpg


stripped the LSD apart

IMG_20240628_212302.jpg


carefully pressing the fresh bearings onto the LSD body

IMG_20240628_215153.jpg


IMG_20240628_215620.jpg


and pressing the bearings onto the new cover plate I machined

IMG_20240628_220205.jpg


IMG_20240628_220428.jpg


now I have a rebuilt Gripper LSD mended 😎🥳

IMG_20240628_221510.jpg


IMG_20240628_221536.jpg
 
2024-06-30 Gizfab BBQ Meet

Met with Jack at 7 in the morning to drive down to Skegness for the annual Gizfab meet

IMG_20240630_075042.jpg


Arrived at gizfab, not as many turned up compared to last yr (prob cos modified nationals show also on the same day) but good to catchup with afew

IMG_20240630_115427.jpg


IMG_20240630_120435.jpg


IMG_20240630_121242.jpg


andrew french came with his blue cabriolet

IMG_20240630_115252.jpg


IMG_20240630_115322.jpg


cars, burgers & catching up with few guys :cool:

IMG_20240630_115757.jpg


IMG_20240630_115855.jpg


later in the day I met up with Todd Blissett who I sold my old BC V1 coilovers to

IMG_20240630_123232.jpg


IMG_20240630_121535.jpg


andrews cab was trailered here cos the fuel pump was seized so he replaced it and got it working

IMG_20240630_144940.jpg
 
took out my spare gearboxes to test fit the new LSD and to see if the diff bearing outer race & shims can be removed easily for adjustment

IMG_20240702_135134.jpg


I fitted the LSD, closed the case and a major issue is it's too tight, it doesn't spin freely, there's too much resistance 😳
even though I machined the cover to the same thickness within 0.05mm I may have to somehow remove the bearings & shims from all my spare gearboxes in order to change the preload.

hmm the outer race doesn't slip out as easy, I think it's tightly pressed in 🤔

IMG_20240702_135934.jpg


IMG_20240702_135938.jpg


I don't have a suitable puller tool & not gonna spend over £150 on a specialisted puller kit online,
so the next thing I had was to modify this old gear puller

IMG_20240702_160120.jpg


I filed the ends to slot in the tight 3mm space behind the outer bearing

IMG_20240702_170136.jpg


IMG_20240702_170431.jpg


was a snug fit, I tried to pull it out but the bearing was seriously stuck and the tool bent/slipped 😒

IMG_20240702_174723.jpg


this kinda puts a roadblock on fitting this diff.
I'll have to design/machine another specialised tool to solve this fitment issue
 
2024-07-04 Diff Bearing Outer Race Tool

After much thought, I figured I could modify this old suspension bushing tool into a bearing puller since it's close to the size of the outer bearing race we're removing

IMG_20240703_142459.jpg


The idea is to machine these 3 fingers (green) which slots behind the bearing through the center

01 fit fingers.jpg


The fingers are then locked together between a pair of nuts & washers

02 sandwich between washers.jpg


The larger cup (yellow) is screwed onto the threaded bar and 'pulls' the bearing out of the gearbox housing.
A thrust bearing (red) helps reduce some friction whilst tightening.

03 puller cup.jpg


The same tool could also be used to reinstall the bearing

04 install bearing.jpg


First task is to machine the removal cup to a larger diameter than the outer bearing

IMG_20240703_221517.jpg


this side will be used for reinstalling the bearing

IMG_20240703_224743.jpg


Next I begin machining the other end of the tool to form the 'fingers' that fit behind the bearing

IMG_20240703_203222.jpg


IMG_20240703_214447.jpg


Carefully cut it into three sections

IMG_20240703_231838.jpg


IMG_20240703_234320.jpg


It fit's nicely within the outer race

IMG_20240703_234207.jpg


IMG_20240703_234213.jpg


I'll try it out tomorrow :cool: 🤞
 
Slotting the three piece finger behind the outer bearing

IMG_20240704_132139.jpg


secure it together with a stack of nuts & washers

IMG_20240704_140607.jpg


IMG_20240704_140615.jpg


Used the large cup to pull it out and it was successful & easy :cool:

So this gearbox uses a 0.6mm shim behind the bearing on this cover housing and the new LSD unit sat much too tight

IMG_20240704_141850.jpg


Used the tool on the bellhousing side

IMG_20240704_144111.jpg


& hmm it doesn't have any shims, suppose you only adjust the bearing preload from one side

IMG_20240704_144347.jpg


the OEM gearbox diff uses a Koyo "High Capacity?" 30208J-N bearing

IMG_20240704_144547.jpg


Whereas the replacement bearing I brought online is an NTN 4T-30208

IMG_20240704_144607.jpg


The service manual says the differential side bearing preload should be 0.30-0.35mm.

spec.jpg


I measured the end play with the new LSD & no shims fitted and it's approx a loose 0.34mm, so with that 0.6mm shim fitted it would squeeze the bearing by 0.26mm making it bind up.

IMG_20240704_160828.jpg


By the manuals definition does the 'side bearing preload' mean it should actually be squeezing the bearing snug & tight by 0.30mm creating resistance?
(cos they also mention the differential should have a 'turning torque' of 1.5-3.5Nm)

or should it spin freely with 0.30mm of loose end play?
(which I feel might cause clunking & wear issues with the final gear)

edit: I googled about side bearings and yeah the bearings are supposed to be squeezed by 0.30mm to keep them secure, accurate & quiet.
so the existing 0.6mm bearing shim seems to be ok.
 
Last edited:
Opened up the 2nd spare gearbox to check & compare the bearings on it.
This box was removed few years ago when the clutch fork snapped off.

IMG_20240704_194205.jpg


Removing the diff bearing, this gearbox uses a thicker 0.68mm shim

IMG_20240704_194817.jpg


To compare the original open-diff with the repaired LSD,
I first tested the open-diff end play without the shims and it measured a huge 0.72mm, so with a 0.68mm shim it's actually 0.02mm loose and has no preload 🤨

Then I fitted the LSD (with the new cover plate I machined as close as possible to the old cover) and the end play was 0.50mm, so it's 0.22mm longer than the OEM diff.
Using a 0.60mm shim that'll give the bearing on this gearbox casing a preload of 0.10mm

IMG_20240704_202112.jpg


Once I remove the current gearbox to fit the LSD I'll have a choice of 3 shims to get the new side bearing preload matched to the gearbox casing :cool:
 
2024-07-06 Raising Engine Crane

My garage has a 10cm high ramp, so every time I use the engine crane I'd have to stack afew wood underneath the wheels to stop it fouling which is a PITA

IMG_20240705_235819.jpg


IMG_20240705_235832.jpg


before.jpg


To fix this issue I removed the dolly wheels

IMG_20240706_124225.jpg


IMG_20240706_125139.jpg


The idea from my calcs is to simply raise the wheels 25mm and it'll clear the ramp

after lift.jpg


made these spacers with some spare 25mm tubing I had

IMG_20240706_134402.jpg


IMG_20240706_140534.jpg


hopefully it'll work when I next remove the gearbox soon

IMG_20240706_141521.jpg
 
Passenger side ball joint was worn out, dry, rusty & seized on

IMG_20240707_154907.jpg


Had to remove the arm for better access

IMG_20240707_163140.jpg


Rust on

IMG_20240707_163153.jpg


Couldn't hammer it out so I used some deep sockets & threaded bar to force it out

IMG_20240707_170128_1.jpg


IMG_20240707_170858.jpg


new bearing fitted

IMG_20240707_171128.jpg


IMG_20240707_174723.jpg


Left side fixed but now the drivers side was also worn and also needs replacing next 🫣
 
Bearing turned up but seemed bit smaller than usual, Doh I ordered a smaller GE17C 🤦‍♂️

IMG_20240712_132453.jpg


Ordered the correct GEH17C and turned up next day

IMG_20240712_123836.jpg


Removed the old drivers side bearing. Hmm the bearing itself is ok & still snug, it's just the outer bearing/housing which is loose fit 🙄

IMG_20240712_184251.jpg


Fitted the new bearing anyway with some extra tape around the outside to take up the slack

IMG_20240712_194549.jpg


Went for a drive to verify it's snug and she finally passed her 222222m milestone 😎🥳

IMG_20240712_205430.jpg


IMG_20240712_205410.jpg
 
Denso plugs I fitted 3yrs ago still looking ok & same gap

IMG_20240716_135702.jpg


Ordered a £15 mini torque wrench to tighten the LSD cover plate evenly

IMG_20240718_120154.jpg


Most of my tools are 1/2" whereas this is 1/4" and I dont have a 6mm allen head for it

IMG_20240718_120403.jpg


So I'll cut & make the tool instead

IMG_20240718_141038.jpg


Now I can torque down my LSD, just need a spare inner spline shaft to align the cover plate

IMG_20240718_143949.jpg
 
Coming back from a wedding party & with rain forcasted, it's time to rip out the gearbox to fit the LSD & weld the noisy loose clutch disc solid.

Drained gear oil still looks fresh since April

IMG_20240721_153711.jpg


Removed the shafts

IMG_20240721_162004.jpg


Dropped the gearbox.

Even after raising the crane 25mm it still fouls the ramp and actually needs an extra 40-70mm rise. The badly loose & sagging castor wheels didn't help

IMG_20240721_214316.jpg


IMG_20240721_214325.jpg


IMG_20240721_214338.jpg


Gearbox removed & can now carry on with the LSD, setup the diff bearing preload, replace input bearing, fix the loose clutch disc, raise the crane further

IMG_20240721_220227.jpg
 
Cleaned & rebuilt the LSD

IMG_20240722_132057.jpg


IMG_20240722_135129.jpg


Torqued & thread locked all the screws to 15Nm.

IMG_20240722_151057.jpg


I tried lock wiring the screws but I was soo rusty it was frustrating & wasted way too much time so left it.

IMG_20240722_151602.jpg


Testing the preloading torque I found that the LSD locking is mainly governed by the traction of the off-side wheel due to the 1-sided clutch pack layout making it very bias.
So while holding the diff casing, spinning the near-side shaft doesn't engage the LSD at all whereas spinning the off-side shaft will lock the diff hard during acceleration and locks very lightly coasting in-gear.

This means it only locks harder during right turns or straight line, less when turning left and doesn't lock at all whenever clutch is disengaged.

IMG_20240722_140925.jpg


Opening the current gearbox, it's abit dirty inside

IMG_20240722_185446.jpg


Gave the casing a little wipe

IMG_20240722_193910.jpg


The old side-bearing outer race are abit worn

IMG_20240722_195110.jpg


So here are the collection of bearing shims from all 3 boxes.
The oldest gearbox uses 0.60mm
The recent gearbox uses 0.68mm
But the current gearbox uses a thick 0.88mm shim

IMG_20240722_194516.jpg


Fitted the new bearings & LSD and the measured end-play is 0.47mm

IMG_20240722_203822.jpg


So I'll fit the 0.68mm shim to give 0.20mm of preload
 
new wheel bearing arrived for when I want to replace the near-side hub spindle one-day

IMG_20240723_114358.jpg


wanted to make a spline tool for checking the LSD diff preload but K11 1.3 driveshafts cost a fortune and the only cheap 24 teeth spline shaft I found online was this landrover discovery 300 24t half-shaft but dunno what the diameter is.

the Micra 1.3 uses a 24t spline with 23.3mm ID & 24.7mm OD
but this landrover shaft is too big at 25mm ID, 26.15mm OD, 32 spline :rolleyes:
so it's abit of a £20 paper weight

IMG_20240723_105124.jpg
 
2024-07-23 Weld Rattling Clutch Disc

The next task to fix is the annoying rattling Blueprint 200mm clutch disc from a Primera 2L diesel.
Flywheel look ok

IMG_20240723_150123.jpg


Flywheel side of clutch is now fully bedded

IMG_20240723_150145.jpg


IMG_20240723_150240.jpg


The PP side is mostly bedded

IMG_20240723_150228.jpg


Old Helix PP is slightly wavy scored nowadays

IMG_20240723_150253.jpg


To open up the clutch disc I grinded the rivets off

IMG_20240723_152008.jpg


carefully pryed it apart with pair of flat screwdrivers wedged on both sides or the rivets

IMG_20240723_153510.jpg


Cover plate off

IMG_20240723_153624.jpg


Little preload ring

IMG_20240723_153642.jpg


& this is the culprit for all that rattling. The inner sprung center which was suppose to dampen the light vibrations are simply too weak, allowing the outer disc to constantly smash against the middle toothed spindle during idle & between on/off throttle

IMG_20240723_153652.jpg


Here's the assembly

IMG_20240723_155020.jpg


IMG_20240723_155119.jpg


IMG_20240723_155133.jpg


IMG_20240723_155157.jpg


To eliminate the useless middle section and allow the bigger outer springs to do the dampening, I simply clamp the dampening cog to the center spindle (locked into position where the engine torque would normally drive the input shaft)

IMG_20240723_162244.jpg


Filled the large gaps with some welds to lock into place yet allowing the teethed section to transfer most of the torque forces

IMG_20240723_163106.jpg


reinstalled the dampening springs

IMG_20240723_165100.jpg


To reattach the cover plate I clamped it down onto each rivet

IMG_20240723_170002.jpg


and hit it with a hot weld

IMG_20240723_170656.jpg
 
Clutch & gearbox installed

IMG_20240723_211045.jpg


All reassembled

IMG_20240723_223443.jpg


Went for a test drive and it worked 🥳

The welded clutch disc is finally quiet & doesn't rattle at idle.

The Gripper LSD with the light preload & regular 80w90 gear oil is quiet with progressive engagement.

When leaving junctions there's soo much traction it doesn't wheel spin anymore.
Steering self-centers hard only when accelerating and yet gentle when coasting.

When turning right with steady light throttle, the LSD starts off quiet but as it begins to engage and the oil is squeezed out of each clutch-disc it gradually begins to make the roulette-table noise & chattering vibration. Whilst chattering, if I apply more throttle it locks harder and goes quiet again probably cos the inside wheel is skipping.

Turning left is silent with a slightly weaker locking action.
 
2024-07-24 Brake Pedal Roller Bearing

The old brake pedal with the tiny loose fitting bearings tend to rattle with the engine (also having the power steering hose resting against the master cylinder doesn't help with vibrations)

IMG_20240725_160335.jpg


So let remove the old small bearings

IMG_20240725_161220.jpg


& replace it with these tighter roller bearings same as the clutch pedal & gear selector

IMG_20240725_163130.jpg


First & drill out & weld a large washer flush to the bracket to make the hole smaller for an M10 bolt

IMG_20240726_154002.jpg


IMG_20240726_155049.jpg


Machined a new inner & outer bushing for the roller bearing

IMG_20240726_211314.jpg


Welded it onto the brake pedal

IMG_20240726_214345.jpg


& reassembled the pedal with zero play

IMG_20240726_215510.jpg


IMG_20240727_131412.jpg


Here's a little feature I never knew till now :unsure: The brake pedal switch actually has a self adjusting ratcheting shaft whereby you can fully extend the tip end

IMG_20240727_131502.jpg


let the pedal return to it's resting point and the switch will adjust it's length

IMG_20240727_131506.jpg
 
Last edited:
2024-08-01 Ultimate Show Car @ Santapod

Going to Santapod from thursday to sun, the morning started off wet

IMG_20240801_082334.jpg


Gathered with TeamWhiteCustom at the Wetherby services

IMG_20240801_094750.jpg


IMG_20240801_100800.jpg


It soon got really sunny warm and we had some food & drink at a pub near santapod :cool:

IMG_20240801_132333.jpg


Entering santapod we lined up at our camp site

IMG_20240801_152208.jpg


IMG_20240801_153040.jpg


The mornings were foggy but cleared into a blazing clear sky by midday

IMG_20240802_073517.jpg


IMG_20240802_104944.jpg


Spotted some Micras at the show

IMG_20240801_210111.jpg


IMG_20240803_212644.jpg


IMG_20240803_111154.jpg


IMG_20240803_111207.jpg


The rave partys at night with my car friends whilst abit drunk was amazing & fun :cool:🥳

IMG_20240802_212801.jpg


We did some light painting at night

IMG_20240801_225010.jpg


At the show they had a dyno for £50.
The last time she was dynoed with 421 headers was 2009 and alot has changed so I was curious to see what her current setup runs like 🤔

IMG_20240802_163346.jpg


Watching from the outside, she has a very deep bass exhaust note.
They only ran 2 out of 3 runs and didn't take it upto 7200rpm redline cos the gearbox was leaking badly underneath



The result was 87hp (could've reached 90hp if they redlined it imo)
and 81ftlb torque.

I converted the units & lined up my 421 header dyno graph (RED) with this current setup (BLUE) and considering it's a different dyno, conditions, fuel, mapping, etc she seems to have lost some power. Maybe the standard manifold with primary cat & larger exhaust is choking her & losing scavenging compared to the old janspeed 421 header & exhaust system with decat?
(note: later I found the throttle cable was too loose & wasn't fully opening WOT)

NA 421 vs 2024.jpg


Our club admin had some spare dragstrip tickets and gave em to me for a go 😁

IMG_20240802_184300 track.jpg


I emptied the car, dropped front tyre pressure, forgot to stiffen the dampers & went for the 1st drag run.
It went ok, the wheel probably spun too much causing lots of hopping on the grippy surface.

She did a 17.46s run @ 76.58mph



Later in the day before the RWYB session closed I brought my friend along for our 2nd run but this time the wheel once again hopped like crazy during the launch and something went bang 😨



From onboard you can hear the driveshaft snap & flapping around before dropping off 🫣
Oh bugger, but she's still moving forward due to her new LSD 💪



Stopped over to look underneath and oh, the snapped shaft was luckily still resting on top of the control arm rather than falling on the track 🙈

IMG_20240802_185653.jpg


The LSD was still able to drive the drivers wheel forward but can't reverse.
So my options to get home were:
*try find a spare 1.3 driveshaft - unlikely on a weekend with poor signal
*phone for breakdown trailer recovery - probably won't accept her from a dragstrip or will take hours of waiting
*slowly nurse her home with a single driving wheel with my club convoy - quickest & cheapest way

IMG_20240802_195617.jpg


We secured the loose shaft with zipties & exhaust clamp to stop it flapping around at high speed or lose more gear oil

IMG_20240804_141515.jpeg


IMG_20240804_141516.jpg


IMG_20240804_200933.jpg


Driving home on 1 wheel with 1.5way diff was weird.
It's like a moped centrifugal clutch whereby the LSD only locks & drives forward when accelerating or going uphill (although it pulls heavily to the left) but soon as I lift the throttle/coast, it detaches & freewheels without touching the clutch 🤨

IMG_20240804_141520.jpg


After 200 miles she was home

IMG_20240804_191358.jpg


At the show brought a gift for her 😅

IMG_20240804_195949.jpg


IMG_20240804_200114.jpg


Looks bit spicier without the dull tyre valve 🤭

IMG_20240804_200229.jpg
 
Last edited:
2024-08-04 Assess Snapped Driveshaft

At home I removed the broken nearside driveshaft

IMG_20240804_202055.jpg


Taking it apart it's clear to see that the rubber dampening collar was trapping moisture & rotting the shaft inside making it thinner, weaker with deep pin holes causing stress risers

IMG_20240804_203006.jpg


Closer look at the gearbox end

IMG_20240804_204229.jpg


& the hub side

IMG_20240804_204245.jpg


I think the deep pitting at this slim section was the starting point of the fracture when I did my 2nd drag run with the wheel hopping & twisting/oscillating the shaft back & forth

IMG_20240804_204539.jpg


Tacked the shaft back together so I can measure the total length to order a new shaft

IMG_20240805_194556.jpg


It's 594mm long, the inner CV joint can slide in/out 40mm

IMG_20240805_205856_1.jpg
 
Last edited:
2024-08-05 Repair Porsche 550 Spyder Gear Shifter

Back from the Santapod trip, a m8 messaged me he had a mechanic whom I knew (was a guy I used to deliver parts to) that needed some custom parts 3d printed for a customers Porsche Spyder 😎

IMG_20240805_115430.jpg


Has a tiny VW engine

IMG_20240806_134554.jpg


IMG_20240805_115613.jpg


So the issue was worn & sloppy gear shifter ball-joints, bushings & UJ's, where spare parts are impossible to find or silly price

IMG_20240805_115610.jpg


We took it apart and saw this lower BJ locating peg is rather botched 🤨

IMG_20240805_120841.jpg


I stripped it apart at home. The botched peg was a short bolt badly welded onto the existing shaft with extra weld added around to increase diameter 🙄

IMG_20240805_131615.jpg


I chopped it off and machined / welded a larger, better fitting pin onto the shifter rod

IMG_20240805_140749.jpg


IMG_20240805_141704.jpg


Then modelled & 3D printed a new ball-joint around the welded peg

IMG_20240805_171511.jpg


IMG_20240805_171531.jpg


The bottom BJ is now snug, precise & the bigger locating peg keeps the rod/porsche gear knob steady

IMG_20240805_171907.jpg


IMG_20240805_171915.jpg


Fitted the upper ball-joint which moves the gear linkages

IMG_20240805_185919.jpg


The repaired gear shifter is complete & operates much sharper now

IMG_20240805_192151.jpg


The next job is to machine new nylon bushings for the rest of the gear linkages in the system 😎
 
2024-08-06 Finding Replacement 1.3 Driveshafts

While I ordered a new 1.3 driveshaft from EuroCarParts for £108, which didn't state which side it was apart from length 594mm which is the near-side, and hasn't arrived yet, I also contacted Jack to see if he has any spares.

Visiting Jack, we gathered & compared a mix of 1.0 1.3 shafts and they all have the same gearbox/hub splines, 23.3mm thick shaft (except for this odd thinner CVT version) but with different sized CV joint & design

IMG_20240806_151346.jpg


Grabbed a pair of good shafts

IMG_20240806_205546.jpg


Looking inside the spare nearside shaft, it's clean & solid

IMG_20240806_220025.jpg


The passenger inner CV joint uses a sliding ball-cage similar to the outer CV

IMG_20240805_203444.jpg


IMG_20240805_194920.jpg


IMG_20240805_194915.jpg


Both outer CV joints uses an enclosed ball-cage design

IMG_20240805_203455.jpg


Assembly was fiddly but the 1st step is locating these pair of wider slots in the cage

IMG_20240806_232555.jpg


They allow the cage to be inserted into the CV housing like this

IMG_20240806_232622.jpg


note the cage has a narrow side...

IMG_20240806_232632.jpg


and a wider side, of which you insert the center piece

IMG_20240806_232639.jpg


like this,

IMG_20240806_232706.jpg


IMG_20240806_232734.jpg


Then insert each ball from the outside, swivelling the center hub

IMG_20240806_232837.jpg


Both Joints overhauled

IMG_20240806_235936.jpg


Nearside driveshaft fitted. Kept the rubber damper off so it never rusts

IMG_20240807_143701.jpg


While I'm replacing the nearside shaft, there's a good chance the drivers side is worn too so may as well replace that same time.

The spare drivers shaft is good too. It uses a roller-bearing style inner CV joint & ball-cage outer CV :unsure:

IMG_20240806_220034.jpg


Swapped the old with new offside shaft

IMG_20240807_155235.jpg


Again, left the rubber damper off

IMG_20240807_160345.jpg


& now she drives fine with no noticable vibrations and good locking LSD 👍

IMG_20240807_195108.jpg
 
2024-08-08 New Driveshaft & Evri Scam

When I returned from Santapod and wasn't sure I was able to find another 1.3 nearside shaft, I ordered a brand new shaft from EuroCarParts for £104. They offered free delivery and estimated to arrive by Wednesday before a car meet, so that would've save me from driving to Stockton twice.

Unfortunately it didn't arrive on wednesday (I fitted the spare shafts I got from Jack instead to make the car meet), Evri only just received my order from ECP on Wed so I was expecting it on Thurs.

Thursday morning 10:30 I was waking up & saw this SMS assuming it's from Evri & was concerned of the message bout my parcel being delayed further

evri copy.jpg


So before my common sense woke up, I clicked the link, it took me to this Evri website where I entered name, addr, mobile number

But it asked for £0.71 process fee to update these delivery details? 🤨
I should've heard the alarm bells but my silly ignorance said meh tiny fee, entered my CC number

Then it had a 60s timer where I'd be sent a verification code by SMS or email but very little time to wait & copy/paste. did it just in time.
then took me to Evri home page.

Only few mins later did I realise I've been fckin scammed looking at the unofficial mobile number and fake foreign link 😱
Dafuq did I do!!?
I'm soo worried with anxiety.

Nothing has been taken out of my CC yet but I froze my CC, reported it as lost to get a new card # (hopefully making the old details I gave scammers void), changed my passwords.
Dunno what will happen but I lost mood to do anything tday 🥸

Checking the official Evri tracking # at 11am said parcel was bigger than expected so they had to send via specialist.
At 3pm it eventually arrived.

So in conclusion, that was either a genuine Evri SMS sent via delivery guy?
Or someone spotted my online purchase & sent me a fake phishing scam while my order turned up anyway?

I feel sick & wanted to immediately return this unopened box to eurocarparts to refund £104 cos don't really need it anymore 😒

IMG_20240808_152453.jpg


I was convinced to keep it & suck up the £104 price cos tbh this new shaft would last lot longer than the 2nd-hand shaft I just fitted 🤔
So I opened it up (eurocarparts was gonna open it to inspect anyway when returning stuff)

IMG_20240808_192755.jpg


Glad I checked cos apart from being clean, it doesn't come with dynamic dampers I also see the shaft is alot thicker 😃

IMG_20240808_193725.jpg


Starline part # 8414610 1462 J0327

IMG_20240808_193749.jpg


The spec of the diff & hub ends match up

IMG_20240808_193803.jpg


IMG_20240808_193812.jpg


The old Nissan shafts were 23mm thick

IMG_20240808_194534.jpg


Whereas these new Starline shafts listed on eurocarparts for the cg10, cg13 & cga3 are a thick 25mm, great for strength

IMG_20240808_194648.jpg


Jack suggested checking the grease cos most of them dont come with enough grease & fail prematurely.
Glad I opened it up & ignore the warranty cos the outer CV had the bare minimum of lube, it'd probably last few weeks before wearing out fast 🙄

IMG_20240808_202749.jpg


The inner CV wasn't too bad

IMG_20240808_202929_1.jpg


Uses the same ball-cage layout but while the old OEM joints have a crimped 'lip' to stop the joint popping apart, the Starline uses a big inner c-clip, great for servicing 😎

IMG_20240808_203145.jpg


IMG_20240808_203430.jpg


IMG_20240808_203606.jpg


Was trying to remove this part with a hammer/punch and also a gear puller but it simply won't budge. It can nudge 0.2mm along the spline but something inside (c-clip?) was really locking it into place and I dont wanna force damage this new shaft

IMG_20240808_210035.jpg


IMG_20240808_210041.jpg


Repacked it with extra grease

IMG_20240808_211024.jpg


Reassembled to install tomorrow

IMG_20240808_211721.jpg
 
Back
Top