wheel info required

[skaboy]

hi just a quicky would 4x100 4stud Honda civic alloys fit a 98 facelift micra these are 16 inch.

cheers

 

[h701micra]

They'll fit the studs just fine. Depending on what civic they came from you'll find the bore is too small
Unless they're aftermarket? If they are you'll probably need spigot rings to suit the micras 59.1 bore

 

[skaboy]

Hi they are off a del sol civic.

cheers

 

[skaboy]

Hi me again lol what about 16in primera gt wheels.

 

[h701micra]

Del sol bore too small
Civic bore too small
Primera = Straight swap

 

[skaboy]

Hi thanxs for that I was about to part with some dosh for the Honda ones I did prefer the Nissan ones.

cheers

 

[karlj]

Aren't primera's 4x114.(whatever)

 

[micra.jas]

Correct but I remember robert had gti wheels on his Si a few years back.

 

[h701micra]

Argh I'm thinking almera
Too many cars going on

 

[davyboy]

Are the primera a straight swap then ??? thinking of getting some for my girl...15" + wheel spacers. I think though I may put low profile tyres on to keep the radius the same.

 

[karlj]

Are the primera a straight swap then?

No

 

[skaboy]

im more confused now than beforeso civic=no,primera=no,almera=yes

 

[h701micra]

im more confused now than beforeso civic=no,primera=no,almera=yes

Yea
Was my bad confusing you

 

[skaboy]

Yea
Was my bad confusing you

You naughty boy

 

[Shamalam]

Almera Yes, Primera No. 16" is a bit much imo. it'll look like it's on stilts if it's not lowered, and if it is it'll rub none stop. Stick with a decent set of 14"'s with good tyres imho.

 

[Andy_S]

I'm running Honda civic 15" no spigots fit perfectly lol


Sent from my iPhone using Tapatalk 2

 

[h701micra]

Type r civic wheels do fit

 

[davyboy]

Found a tidy set of 15" multi fit with 195x50x15 and almost new tyres. Are they too wide ???? Mine is lowered on the front, standard on her backside. £200 - good deal methinks, will have to paint them black though.

 

[skaboy]

Hi davyboy I think they will but im not 100% one of the other lads on ere should know ive gone for 6in x 13in now and a 40mm drop alround.

cheers

 

[Andy_S]

Mine are 195/45/15 on 35mm springs and are ok


Sent from my iPhone using Tapatalk 2

 

[h701micra]

Ive a set of 195 lowered approx 50-60mm runs fine

 

[davyboy]

My thanks to you all. If they are still for sale - I'll have em. Thanks again.

 

[davyboy]

My thanks to you all. If they are still for sale - I'll have em. Thanks again.

Missed them wheels by one day, darn!!!!!

 

[h701micra]

Better luck next time mate

 

[davyboy]

Got my eye on two more sets, waiting for info. Crossing my fingers here.

 

[Shamalam]

Any ever had any 175/60/13's? If so what they like?

 

[h701micra]

Comfy ride. Aren't good on lowered cars they rub badly. On standard cars they do still rub on lock (size of the sidewall)

 

[Shamalam]

Hmm ill have a ganjeez when I get em, not planning on dropping that low so shouldn't be that much of an issue.

 

[MicrAde]

Any ever had any 175/60/13's? If so what they like?

Got them on my SR alloys, cheap enough, comfy, grippy but don't look particularly great, little bit chunky. I'm lowered approx 50mm and have had no contact issues at all

 

[Shamalam]

Fine by me, I'm going for performance over looks.

 

[MicrAde]

Should be well away then mate

 

[Enuo]

Standard tire fitment on my car (super s), lowered at least 80mm on front on 5j steels and no rubbing, 15mm is clearance either side between tire wall and inside of arch at the rear. They're a bugger to get hold of part worn.

 

[h701micra]

I'm guessing k11 has more arch space than a k10

 

[davyboy]

Just got my wheels, Wolfrace with a decent set of rubber 195x45x15...alloys are in a fair condition. Polished alloy with a few minor scratches, I'll stick em on and see what they look like before I decide to paint em (peugot grey) or not.
The fella threw in 4x locking wheel nuts, never used...all in £90 WHAT!!!!! lucky day - gonna put a fiver on the lottery...must be my lucky week.

 

[MicrAde]

Just got my wheels, Wolfrace with a decent set of rubber 195x45x15...alloys are in a fair condition. Polished alloy with a few minor scratches, I'll stick em on and see what they look like before I decide to paint em (peugot grey) or not.
The fella threw in 4x locking wheel nuts, never used...all in £90 WHAT!!!!! lucky day - gonna put a fiver on the lottery...must be my lucky week.

Pictures!!

 

[davyboy]

Pictures !!!! OMG !!!! I've tried to do that so many times I must be a gold member on photobucket by now.
Need a lesson from someone, Jen had a go, did all of that ...still no piccies Don't seem to work for me, but, I'll have another go tomorrow. DO NOT hold your breath!!!!!

 

[davyboy]

Had my alloys on this afternoon, and looking good. No rubbing on full lock - delighted.
However I need spigot rings to centralise them. Here's the rub !!!! what size do I need ???? Didn't know there were different sizes (why do they do that!!!!) 52 plate 1.4 twister, anybody know ???? or what do I measure to find out... the centre hub ????
Any replies much appreciated boys and girls

 

[karlj]

What's the centre bore for the alloys?

K11's have a cb of 59.1

 

[davyboy]

What's the centre bore for the alloys?

K11's have a cb of 59.1

Brilliant karlj, I'll order them now, many many thanks

 

[MicrAde]

What's the centre bore for the alloys?

K11's have a cb of 59.1

72.6 for wolfrace..................usually

 

[MicrAde]

So you would require 72.6-59.1 spigot rings. It will be worth measuring the CB of the alloy though to be on the safe side

 

[Skinner_87]

Had my alloys on this afternoon, and looking good. No rubbing on full lock - delighted.
However I need spigot rings to centralise them. Here's the rub !!!! what size do I need ???? Didn't know there were different sizes (why do they do that!!!!) 52 plate 1.4 twister, anybody know ???? or what do I measure to find out... the centre hub ????
Any replies much appreciated boys and girls

As Karls said micra spigot is 59.1

your running wolf race now? Wolfrace centre spigot is 72.6 if i remember right so you will need these:

http://www.ebay.co.uk/itm/4-X-72-6-...Wheels_tyres_Trim_Nuts_ET&hash=item2ec7e48978

 

[davyboy]

Hah hah, now I understand, dopey me one measurement for the centre bore on the axle, and one for the same on the spigot.
Bloody brilliant boys...a big thanks from me...cheers

 

[davyboy]

All ordered, thanks skinner 87 that made it easy for me. You boys ever down Cornwall way - I owe you a pint or two.
Thanks again

 

[MicrAde]

All ordered, thanks skinner 87 that made it easy for me. You boys ever down Cornwall way - I owe you a pint or two.
Thanks again

Jealous much!! I love Cornwall, lived there for 18 months and would move back in a heartbeat if my kids weren't up here

 

[davyboy]

Jealous much!! I love Cornwall, lived there for 18 months and would move back in a heartbeat if my kids weren't up here

Gods country mate, born here and will die here. I live 5 minutes from the sea and 5 minutes from the countryside...what else could anyone want....OH!!!!!! and I have a k11 - utopia or what.​

 

[karlj]

Ohh a free pint I'll see you in 3hrs

 

[davyboy]

Ohh a free pint I'll see you in 3hrs

You must be Bristol way if your 3 hrs away - name the pub, anywhere around the Falmouth area and I will be there !!!!!

 

[karlj]

I don't know Falmouth and the missus said no

 

[davyboy]

I don't know Falmouth and the missus said no

I know Falmouth and leave your missus..........................................................................................................................................................................................................................................................................................................................................................................................NO, NO!!!!!!! only joking ....I don't know Falmouth. LOL.