Micra K11 1.4 died and doesnt start. Crank sensor wiring?

[2jzhx60]

I was out driving the car and it suddenly died and doesnt start. It will crank but doesnt start.

I hooked up a generic OBD2 reader and it gives a C0335 code which I couldnt find anywhere. I also dont see RPM data ion the reader when cranking the car. So I started to check the crank and cam sensors and wiring. Cleaned the crank sensor and measured the voltage coming to the sensor and they seem odd. I can get earth, but on the power connector I only get +1.5v and the same to the signal wire.

I measured the cam sensor and that gets +12v ang +5v which seem correct.

What could cause this? Could it be a bad ECU? I couldnt find a wiring diagram to the coil pack K11 version, where can I find it? There was discussion about some Italian or Russian versions but I couldnt find links for them.

 

[frank]

Wiring Diagram For K11 1.0

Does anybody where I can get a wiring diagram showing wiring to coil packs? I want to wire up a tachometer and the adaptor needs to be connected across the coil packs.

www.micra.org.uk

 

[2jzhx60]

Thank for that Frank.

 

[Bilawalkn]

I was out driving the car and it suddenly died and doesnt start. It will crank but doesnt start.

I hooked up a generic OBD2 reader and it gives a C0335 code which I couldnt find anywhere. I also dont see RPM data ion the reader when cranking the car. So I started to check the crank and cam sensors and wiring. Cleaned the crank sensor and measured the voltage coming to the sensor and they seem odd. I can get earth, but on the power connector I only get +1.5v and the same to the signal wire.

I measured the cam sensor and that gets +12v ang +5v which seem correct.

What could cause this? Could it be a bad ECU? I couldnt find a wiring diagram to the coil pack K11 version, where can I find it? There was discussion about some Italian or Russian versions but I couldnt find links for them.

View attachment 74815

Hi i got the same problem did you found any solution for it!?

 

[Bilawalkn]

I was out driving the car and it suddenly died and doesnt start. It will crank but doesnt start.

I hooked up a generic OBD2 reader and it gives a C0335 code which I couldnt find anywhere. I also dont see RPM data ion the reader when cranking the car. So I started to check the crank and cam sensors and wiring. Cleaned the crank sensor and measured the voltage coming to the sensor and they seem odd. I can get earth, but on the power connector I only get +1.5v and the same to the signal wire.

I measured the cam sensor and that gets +12v ang +5v which seem correct.

What could cause this? Could it be a bad ECU? I couldnt find a wiring diagram to the coil pack K11 version, where can I find it? There was discussion about some Italian or Russian versions but I couldnt find links for them.

View attachment 74815

Any solution did u found!?

 

[Bilawalkn]

I was out driving the car and it suddenly died and doesnt start. It will crank but doesnt start.

I hooked up a generic OBD2 reader and it gives a C0335 code which I couldnt find anywhere. I also dont see RPM data ion the reader when cranking the car. So I started to check the crank and cam sensors and wiring. Cleaned the crank sensor and measured the voltage coming to the sensor and they seem odd. I can get earth, but on the power connector I only get +1.5v and the same to the signal wire.

I measured the cam sensor and that gets +12v ang +5v which seem correct.

What could cause this? Could it be a bad ECU? I couldnt find a wiring diagram to the coil pack K11 version, where can I find it? There was discussion about some Italian or Russian versions but I couldnt find links for them.

View attachment 74815

Any solution did u found

 

[Twincam-Alex]

Try this link looks a good starting point.

P0335 – Meaning, Causes, Symptoms, & Fixes

Check engine light code P0335 means Crankshaft Position Sensor “A” Circuit Malfunction (Bank 1). Find out how to fix it in this article!

www.fixdapp.com