Alloy wheel sizes

[CMF_Virusash]

Hi its me again, need a little advice
i have inhereted a five set of 195/60/14 alloys and tyre by a scrap dealer and they are used nissan ones, i just wondered if they can go onto my 1996 k11 nissan micra 1.0. do i need to get any additional stuff to fit these on?

thanx for the help

 

[CMF_kneival]

You wont need anything additional to fix them on, they will be fine as long as your car is not lowered a huge amount (altho being 14s they should be fine anyways)

Hopefully they have the same stud pattern as the micra, only way is to try and enjoy!

 

[CMF_Virusash]

hi again, i have a BIG problems now, the alloys i inhereted are from a nissan primera and the holes for the wheel fixing do not match the micra wheel fixing
what can i do to solve this problem?????

Thannx for ur help

 

[CMF_nz_aj]

Your micra is 100mm PCD, a primera is 114mm.
Best advice is sell them & get some that fit.
It would be expensive to fit hubs with a 114mm stud pattern.
Adaptors would push the wheel to far outboard & screw up the steering geometry.
Drilling holes more in the factory alloy is probably not a safe thing to do.

 

[CMF_NotAnotherSSS]

You *could* get the rims re-bored to suit the 4x100 stud pattern, but I would only do it after consulting an engineer.

Would probably be cheaper to just sell the primera rims and buy some almera rims.

 

[CMF_Virusash]

Thanks u guys, one more question can either of these cars alloys work on my micra k11
nissan sunny
nissan pulsar
nissan 200sx

thanx for ur help, btw i have sold those primera and got a good profit.

 

[CMF_Alex_B]

n14, n15 pulsar alloys will fit as they are 4x100PCD, i think some of the sunny wheel will too? Silvia/200SX won't fit,

Alex

 

[CMF_Jindrich]

I found a table for a better outlook:

4x100 are: Micra (K10, K11), Almera (N15), Sunny (Y10, Y10L, B12, N13, N14), 100NX (B13).

BUT 4x114,3 are: Pimera (P10, P11, W10), Prairie (M11), 200 SX (S 13), Almera (N16).
I hope, it will be helpful.

 

[CMF_Virusash]

Hi again will these fit my little K11?

These are from my sunny GTI-R which i have been breaking. The size is 185/60R /14.

 

[CMF_NotAnotherSSS]

yes they will fit but the tyres might be too large and give flase readings from the speedo.

 

[CMF_Virusash]

why and how would i get false reading when using those alloys? sorry im a little new!

 

[CMF_kneival]

If the circumference of the new wheels are different to the old then the car will be travelling further/less further each time the gearbox cog spins. As the speedo has been calibrated with the stock wheels on fitting new ones will throw the speedo out by a %.

You can overcome this by fitting thinner tyres such as 45 etc until the circumference is nearly the same.

 

[CMF_elx]

hey im running those rims, i've wrapped them in some 185 55 14's and my speedo seems to be accurate (based on those damn slow down signs that light up when your too fast). I chose the 185 55's over 45's as running low profiles is a mistake where i live. Far too many pot holes.

 

[CMF_elx]

I think there meant to run 195 50 14's.

 

[CMF_Virusash]

one more question, wat are offsets and wats the best which will go onto my k11 micra?

Thanks again
im still learning!

 

[CMF_elx]

http://www.discountedwheelwarehouse.com/Wheel_Fitment_Guide.cfm

That should help you out.

 

[CMF_Nitro Darkside]

the max size I can put on my micra is 175/65/13

Italian law..