Search results

  1. C

    Aussie n14 GA16de into 95 K11

    just brute force rudy
  2. C

    Crank timing waaaay out?

    ecutalk mate, there are others too :) http://www.micra.org.uk/threads/tost-the-official-spam-thread.53370/page-63#post-651217
  3. C

    1.3 cams fitting instuction and cam timing advancing instructions

    there are some different pinouts on the pre-nats and nats2/5 ecu,s sean, there are some wiring diags about and the coilpack (post 2000) bosch motronic setup is totally different
  4. C

    Aussie n14 GA16de into 95 K11

    this guy,s n16 QG18 had an RS5F30 g/box originally eh ! http://www.then16files.com/
  5. C

    Aussie n14 GA16de into 95 K11

    these are glens pic,s eh rudy, and the QG has a cast iron block too :)
  6. C

    1.3 cams fitting instuction and cam timing advancing instructions

    yes same spec sean, they squeezed another 5hp via the more sophisticated motronic ecu i guess
  7. C

    Crank timing waaaay out?

    yeh, disconnect the tps and blip the throttle i think mate, but i dont think that is 100% tho (depends on a correctly set idle control valve i believe) i prefer to run the ecutalk screen on the lappy and compare the data with the strobe personally, ie watch them running both together at idle...
  8. C

    Crank timing waaaay out?

    left to right is 5 atdc then the yellow tdc, then 5 btdc etc pierce but you need to lock it in base timing idle mode, or else use a diag connector and ecutalk software
  9. C

    1.3 cams fitting instuction and cam timing advancing instructions

    advancing the cams only suits a daily driver sean, it basically corrects the slack from the worn chains and restores the lowdown grunt that the car had when it left the factory, yours will be ragged around an oval at higher rpm than that
  10. C

    Sr16ve neo vvl

    turbs (radek/TMRS) did an SR16VVL build on here iirc ?
  11. C

    CVT Shuddering

    sounds a bit terminal mate, there is a diagnostic procedure you can try tho eh
  12. C

    RS5F31A gearbox into K11

    any protons in aus rudy ? https://micra.org.uk/cmf/message/80024
  13. C

    CVT Shuddering

    i just filled with generic ATF on the one i did mate
  14. C

    Aussie n14 GA16de into 95 K11

    lookin good rudy :) there is a fair amount of sideways give in the shafts if you want to shift the mounts (ie, remove the rubber and rotate/refit) and my front mount was binned years ago eh
  15. C

    CVT Shuddering

    does,nt sound like g/box to me, else it would shudder under load too you get a mad shudder if the fueling goes very lean, i would try a volt meter on the middle lambda wire (it should read .3 to .6v under light throttle)
  16. C

    RS5F31A gearbox into K11

    nice one rudy :) what will be the gains ? and i checked some CVT shafts and diff a while back, they were just normal splines
  17. C

    throttle body question

    no probs rudy, but 2kg+ is crazy postage money tho eh
  18. C

    throttle body question

    what will you do for a maf if you use that t/b tho rudy ? and there is some GA info here eh :) http://www.micra.org.uk/threads/ga16-swap-info-pool.57739/
  19. C

    throttle body question

    yes, no probs rudy :)
  20. C

    CG 13 MASS Air flow sensor

    same throttlebody aruna, but i doubt if its the maf at fault tho, idle control valve maybe ?
Back
Top