Search results

Yeah, but black is free [emoji106][emoji106] Sent from my iPhone using Tapatalk

Hmm, i may have those of you at some point then mate Gunna set this ecu up how I know for know (batch and wasted spark) .......I still don't know whether this ecu works or not (Was given to me for free) Sent from my iPhone using Tapatalk

I don't have any micra coil packs mate (on the mini) ......and that cam plate I got from you has gone walkabouts [emoji848] Apparently I can run the ford coil pack straight from the ecu [emoji106] Sent from my iPhone using Tapatalk

Got some bits through Trigger wheel, crank sensor .....and ford coil pack The ecu I've got on the mini is the same as this.......I'm using the micra coil packs driven by the ecu........surely I can do the same with this thing (I don't have the edis module) Oh yeah, still haven't learnt...

These are 274 degrees and 0.355 lift......what he recommended with all the other things I've done and going to put on Il have to whip out the cams again and see what these top shims are.....then figure out the correct sizes and get back to you mate.......maybe next week if I can find the time...

Because I'm a child and impatient, I started the engine as it is I let it rev in its own for 10-15 mins to warm it up[emoji106] Is a bit tappy, so will definitely have to swap some shims about. Went for a quick drive......above what I think is 2-3k, it goes mental lol [emoji23] What I...

Haha, I guess so mate......same as before? Is there any bedding in procedure I need to do......like keeping a certain rpm for a few miniutes Sent from my iPhone using Tapatalk

Just swapped some about. So would I be able to use it like this? Sent from my iPhone using Tapatalk

Right, I've put all the bottom shims in and this is what I've got with the feeler gauge Top numbers, inlet cam Sent from my iPhone using Tapatalk

274......think that's what he said, gunna be messing about with shims tomorrow Geoff sounds like a nice bloke, and was really quick with the turn around [emoji106][emoji106][emoji106] Sent from my iPhone using Tapatalk

I just got these today from auto sprint .355 lift Sent from my iPhone using Tapatalk

Just so I'm clear......I'm measuring this gap? Sent from my iPhone using Tapatalk

Cool, cheers Looks Like this will take a while!! I don't need the sprocket/chain on do I? Sent from my iPhone using Tapatalk

Il have a look. Don't have to worry about the centre bit then? Also......I've got what clearances to look for.........but no idea of where to check [emoji23] Sent from my iPhone using Tapatalk

Also......cam bloke said to put the shims under the bucket......there's a raised part under there, do I have to cut/grind a bit outa the new shims so they sit flat inside Sent from my iPhone using Tapatalk

Got the cams back from autosprint..... And a pack of shims of frank [emoji106] Now gotta fit them lol [emoji23] Gunna take note of the shims height, and guess il move/grind them about till I get the right clearances ...........what should I be getting and where should I be taking...

Started the loom for the ecu Bought a 165/45/15 tyre to see what it'll look like on these wheels.......think it'll be ok with more lows[emoji106] Sent from my iPhone using Tapatalk

Sent cams of today for a regrind Sent from my iPhone using Tapatalk

Got the ecu.....looks ok to me, I'm hoping it was down to the previous wiring attempt on the plugs that was giving my friend the issues, he seemed to think the ignition drivers had burnt out Either way, il use this to make up the loom and stuff, it's exactly the same as my old ecu that was on...

Got some mini alloys for nowt, fixed a dudes compressor and he had these [emoji106] Bored out the centres.....need some better Tyres though Sent from my iPhone using Tapatalk