andy's latest activity

  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-03-18 Rebuild Garage Roof My garage roof consists of a steel mesh cage covered with a mess of clear corrugated sheets, which tends...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-03-08 Check Peugeot 307 Fuel Pump After seeing the terrible rusty debris in kassandras tank (suspecting it's either from the old...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    It's been 1yr since I last checked the compression and 2yrs since checking valve clearances 👀 Insides look good from regular 6mth...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    The caliper carrier has upto 2mm gap from the disc edge Whereas the caliper sits abit closer upto 1mm gap from the disc 🫣 notice...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Recently noticed hearing a slight rubbing noise once-per-wheel turn only at low speed, shortly after applying brakes and after driving...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-17 Walbro GSS250 Fuel Pump Detailed Look For a closer look at how the Walbro 255LPH internal gear type pump works and it's...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-15 Replace Walbro GSS250 255lph Fuel Pump With approx 75% fuel level I removed the fuel pump assembly out of the tank. Not a...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Didn't have much energy today but I managed to crimp the new relay wires together Reassembled the loom & dash Couldn't be bothered...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Trying to reach that small plug behind the fuse box was difficult, so there's no option but to remove the dashboard for better access 🙈...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Looking deeper into the service manual wiring diagrams, I managed to trace where the fuel pump circuit goes and potentially locate Plug...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-12 New Walbro GSS250 Fuel Pump The new Walbro GSS250 255lph fuel pump I brought on ebay arrived today, same as the current one...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    Today I did a more thorough check of the voltage drops across the whole fuel pump circuit & plotted the values on this diagram Most...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-11 Test Fuel Pump Voltage Drop In preparation for replacing the Walbro fuel pump, I figure it's best to first check if the pump...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    The other day whilst driving down to Leeds I noticed the mixture goes oddly really rich 13afr while cruising at 60-70 but fine at low...
  • A
    andy reacted to pollyp's post in the thread PollyMobiles Rebuild with Like Like.
    2025-02-03 Solid Steel Steering Rack Mount The old 3D printed solid plastic rack bushing was once again worn loose allowing the PAS...
Show older items
Back
Top